1. Fitting a Cold Air Intake (DIY Kit & Pre-packaged)
(DIY Articles/Performance Do It yourself)

... cone air filter 5)  3 1/2" Diameter Dryer Ducting Hose 6)  Assorted PVC Elbows for Joints 7)  Dryer Hose Clamps and PVC Glue 8)  Air Scoop for mount under front bumper Step 1 - Open hood and remove front ...

2. DIY Clear Turn Signals
(DIY Articles/Performance Do It yourself)

... removal of the turn signal units and may also require the use of a heat gun to remove the factory orange turn signal lense. This is a project to DIY your factory supplied lights into clear light, but ...

3. Front speakers in an SF5 forester.
(Install/Car Audio Installation)

... cutting metal.) Sound Deadening material. I'll be using Dynamat Extreme. Wax and grease remover. Rags 18mm thick MDF to make a spacer. Speaker wire. Black spray paint. Duct tape. Heatshrink. ...

4. Recone subwoofer or any speaker
(DIY Articles/Car Audio Do It Yourself)

... razor blade (to remove the old cone/coil) - A metal scribe (very handy, you'll find ways to use it) - A small flat screw drive - Soldering iron & solder - Bottle of Acetone (from hardware store) Reconing ...

5. Installing a Head-Unit into a 2002 Subaru Forester
(Install/Car Audio Installation)

Installing a Head-Unit into a 2002 Subaru Forester OK, i will take you through how to remove the stock unit and replace it with an aftermarket unit.  This is what the stock unit should look like (if ...

6. Weight Reduction Guide
(DIY Articles/Performance Do It yourself)

... removed your car will have a better horsepower/weight ratio and will not only accelerate faster but also corner and handle better while getting better gas mileage. Saving 22lbs of weight is like adding ...

7. Headunit Installation in 2002-2006 Lancer
(Install/Car Audio Installation)

...  ·         Once you have the surround removed, you’ll notice 2 Phillips head screws on each side of the stereo, undo these 4 screws and store in a safe place. ·         ...

8. Head - Unit Removal and Installation - 2003 Mitsubishi Magna
(Install/Car Audio Installation)

OK today we have a 2003 Mitsubishi Magna tutorial on how to remove the standard stereo and then install a new aftermarket one. This may apply to other models of the Magna and varients sold elsewhere ...

9. Headunit Installion in VN-VT Commodore, Calais, Ute & Statesman
(Install/Car Audio Installation)

... the gear shift into D, and make sure the hand brake is on FULL. Undo the zipper on the hand brakes booty. Open the center console, remove the junk, and remove the carpet. ÂÂ Undo the 2x 10mm ...

10. Installing a Head-Unit Into a VT-VX Commodore
(Install/Car Audio Installation)

... stereo, the double DIN means its double the size of a standard stereo head-unit (DIN). To overcome this i use a single DIN pocket, mounted below the new stereo. Â Step 1: Remove the standard stereo. ...

11. Eliminate Engine Noise
(Electronics/Auto Electrical for the Car Stereo)

... varies with engine speed. If you have the latter type of noise you might want to check your ignition system and leads to make sure they are operating correctly. ÂÂ How to remove it: Â If you ...

12. Headunit Installion in X2-X3 Hyundai Excel & Accent
(Install/Car Audio Installation)

... on. On the underside of dash panel, remove the two plastic plugs. Undo the 4x 10mm bolts holding the under-panel guard in place (there's one on each corner)Â Look up under the dash, next to ...

13. Building Your Own Subwoofer Enclosure
(DIY Articles/Car Audio Do It Yourself)

... attach it to the base and sides. Then screw it loosely. Do the next side drilling the taps and screwing. 3. With the final end drill the tap holes, but then remove it and apply glue to its edges. Now ...

14. Desolder and Test the Field Effect Transistors (MOSFET) in your amplifier
(Electronics/Car Audio Electronics)

... wick/braid (I recommend Servisol or Goot Wick brand braids) - Digital multi-meter with continuity function1. First things first, remove the FET's from the PCB ! You cant test them in-circuit. ...

15. Diagnosing amplifier protection mode faults
(Electronics/Car Audio Electronics)

... hot) and goes into protection mode, verify your speakers impedence is within the amplifiers load specification. If they are, then give your amp more ventilation. 5. Remove speaker wires from amp and ...

16. Getting into SPL Competition, the begginers guide.
(Technical/Theory and Physics)

... to your SPL. To find it, use a sealed box and follow the same steps as outlined above. Then, remove the sealed box from the car and place it in an open air area. With the mic/sensor 1m away from the speaker’s ...

17. Painting interior panels
(DIY Articles/Performance Do It yourself)

... clean clean ! Spray in a clean area and keep dust away. First off, scrub the plastic bit down with Prepsol. This removes grease, wax, dirt, snot, etc from the surface for maximum adhesion. Next, ...

18. VIDEO Honda Main Relay Repair
(Electronics/Auto Electrical for the Car Stereo)

... this article on how to remove and repair your main relay to resolve problems with your Honda not starting. http://www.youtube.com/watch?v=kY_GnVwOF9U  ...

19. VIDEO Removing Door Cards
(Install/Car Audio Installation)

...  Follow our video tutorial to learn how to remove the door cards from your car. While we use a Honda CRX with manual windows, the steps are pretty similar for every vehicle out there. A DecibelCar.com ...

20. VIDEO Replacing Windows
(DIY Articles/Performance Do It yourself)

VIDEO Replacing Windows Ever had your window busted out ? We did, so here's a nice How To on replacing your door windows, including how to remove the door cards. http://www.youtube.com/watch?v=CfCIwDsMRE8 ...